Place a towel or large rag on the shower floor to protect it from possible damage if you happen to drop a tool. Also cover the drain so that any of the small parts from the showerhead don't accidentally go down it. Remember not to force anything. Whether you're taking off the showerhead or putting it back on, don't tighten it so tightly that you damage or crack something and then need to take on a larger project. Since you have the showerhead off, now is a good time to clean out the showerhead, especially if you've noticed decreased flow.
Oftentimes, there can be mineral deposits or sediment left by hard water on the interior of the showerhead or at the pipe stem where the pipe connects to the showerhead. This can significantly affect water pressure and flow and can contribute to a leaky showerhead.
In a small cooking pot or pan , mix water and three cups of vinegar and bring it to a boil. Once it's started to boil, turn off the heat. Place the showerhead minus any rubber parts that can be removed into the solution and let it sit for approximately 20 to 30 minutes. Then remove, rinse and scrub the inside and outside jets with an old toothbrush; do this until no deposits remain. Don't overdo it with tape though.
Wrap a thin strip around the threads at the very tip of the pipe stem. Screw the showerhead back on by hand-tightening it until you can't turn it anymore. Then use pliers to give it a final turn.
Remember not to turn too hard or you could break the showerhead or pipe. Turn the water back on and then run your shower for a few seconds. Turn it off. Wait a few minutes and then check to see if there still is a drip or leak. If you've fixed the showerhead and a leak persists, you may have a leak in the shower faucet. Usually, this is from a worn-out washer on the shower stem , which can easily be replaced. You don't need to call a plumber. Follow these steps to do it yourself.
As you did with the showerhead, you will need to cut off the water supply to the shower at the water main. Next, open the faucet and let water drain out.
Keep a towel on hand to soak up water that may be released from the pipes once you remove the faucet. Because you will be standing in the tub or shower to do this project, be sure that the floor surface is dry. Any moisture could cause you to slip and fall. How you disassemble it depends on what kind of faucet you have: one-knob or two-knob style.
Over time, these wear down, and when they do, water starts to leak out. Working out why your shower is leaking is often a process of elimination, and the next section guides you through the steps you should take to get to the bottom of the problem. Before you get started, turn off the water supply to avoid any unpleasant surprises later on. Remove your showerhead from the hose, taking care not to lose the O-ring or rubber washer, then soak your showerhead in vinegar for at least 30 minutes.
Rinse it with water and use an old toothbrush to remove any stubborn dirt, grime and limescale, paying close attention to the individual nozzles. Rinse it again, then set the showerhead aside. Learn more about how to clean and descale your showerhead with our step-by-step guide. Your O-ring or rubber washer is the component that prevents water from leaking between your showerhead and hose.
Soak the shower head overnight in white vinegar to soften the mineral deposits, and scrub away any remaining residue with an old toothbrush before reinstalling. Washers and O-rings form watertight seals between connections on a shower head , but they can harden or split over time, which allows water to leak out. This type of leak is especially common in shower heads with swivel connections, which have a seal behind the swivel assembly.
If you suspect a worn seal, remove and disassemble the shower head to replace the washer or O-ring. Tip: When purchasing a new plumbing seal, take the old one with you to the hardware store to ensure that you bring home an exact match. Compression faucets have two different handles: one hot and one cold.
If you have a compression-style shower that leaks when turned off, the problem could be a worn washer in the assembly. First, determine which handle, hot or cold, is causing the leak by feeling the temperature of the dripping water. Then, turn off the water supply and give this fix a try: Remove the faulty faucet handle, which is held in place with a screw located below the handle or hidden under a pry-off cap.
Slip off the cover trim to gain access to the faucet stem, which is secured with a hex nut. Then finish reassembly. Finally, seal the trim to the wall with tub caulk. Shop for tub caulk online. If your shower has a leaky Delta shower faucet, here is how to stop the leak. Shut off the water supply to the shower and protect the surface of the tub or shower floor.
Then remove the brass bonnet with a pair of locking jaw pliers, turning it counterclockwise. Feel inside the valve area for any deposits or loose particles, and clean with a rag. Push it firmly in place.
Be sure the threads grip properly. Hand-tighten, and then use locking jaw pliers to snug it down. Clean the wall where the escutcheon plate goes, and then put the outer sleeve back on the cartridge and push it into place. Replace the escutcheon plate and handle. As when working on other types of shower valves, start by shutting off the water supply and protecting the tub and drain with rags. Ideally, your shower plumbing will have a local water supply valve that you can shut off similar to the valve under a sink that is accessible through a removable panel.
Open a nearby faucet to empty the shower pipes. If you can prove that you bought their valve after , they will send you free parts. You can also buy a replacement valve on Amazon. Use a Phillips screwdriver to remove the screw, turning it counterclockwise. Then remove the handle assembly. If the escutcheon trim is caulked to the wall, use a sharp knife to cut the seal. Be careful not to scratch the surfaces. Remove the plate from the wall. Again, turn them counterclockwise to remove them.
0コメント